Hair Dryer nanocare EH-NA0K Mode, how to use, design, environmental friendliness

Temperature is the key to achieving glossy hair. The Hot/Cold Alternating Mode automatically switches between warm air and cold air. Heating the hair with warm air smooths out any frizz, and cooling it with cold air keeps it in that state. Without the frizz, the surface of the hair is regular and reflects the light, giving a smooth and glossy finish to your hair.

[Trial method]
The hair was dried until completely dry using a dryer as one would normally do after washing it. In one case Hair Dryer nanocare with built-in Hot/Cold Rhythm Mode was used, and in the other case it was not

• Panasonic survey

• Effects vary depending on usage environment (season, temperature/humidity, etc.) and the individual

The Intensive Hair Tip Care Mode uses the sensor to automatically check the ambient temperature and alternates hot and cold airflow at the right intervals and air volume to provide the perfect finish for your hair tips. The weak flow is easy to direct and enables you to provide intensive care for all your hair tips.

• Perform when your hair is almost dry

[Trial method]
The hair tips were dried completely using a dryer as one would normally do after washing the hair. In one case Hair Dryer nanocare with built-in intensive hair tip care mode was used, and in the other case it was not

• Panasonic survey

• Effects vary depending on usage environment (season, temperature/humidity, etc.) and the individual

[Trial method]
Bunches of hair were finger-combed while being dried. The ratio of hair tip spread was 0.66 when dried with warm air (with airflow on “HIGH”) as compared to 0.55 when the Intensive Hair Tip Care Mode was used as far as the hair tips (for approx. 24 sec) after the hair was 90% dried with warm air (with airflow on “HIGH”)
The inverse value of the ratio of hair tip spread was calculated to give a rate of 1.3 times more sleekness

• Panasonic survey

• Effects vary depending on usage environment (season, temperature/humidity, etc.) and the individual

Residual moisture on the scalp surface can cause unpleasant sensations such as clamminess. Scalp Mode gently dries your scalp with pleasantly warm air at a temperature of approx. 60℃^*1.

• Perform when your hair is about two-thirds dry

• If you feel cold due to the surrounding air temperature, use the HOT setting and aim the airflow towards your head while keeping the hair dryer away from your scalp

Aiming at the face for about one minute locks in skin hydration. Recommended for use on skin after taking a bath, which tends to become dry easily.

• Keep your eyes closed while using this mode.

• Please follow your usual skincare routine, such as using a toner or emulsion.

• If you select “SKIN” while the airflow is set at “HIGH” or “MEDIUM”, the airflow setting will switch to “LOW”. Press the air temperature button to return to the original airflow.

• If the airflow button is pressed while using SKIN mode, the airflow light will flash twice and changes to the airflow cannot be made.

Attach the Nightcap Nozzle when your hair is about two-thirds dry.

[How to use]

• Attach the Nightcap Nozzle

• Select HOT with the air temperature button, and aim the airflow at your hair while brushing it with your fingers from the inner sections

• Aim the airflow at your hair while brushing it with your fingers from the top section to the ends. Repeat on the opposite side

• Use SCALP mode before using the Nightcap Nozzle

Dry your hair with the Quick-dry Nozzle installed in the dryer.

• The Quick-dry nozzle can be used as is, because it is installed inside the main unit

Attach the Quick-dry Roots Nozzle and start drying your hair.

Attach the Styling Nozzle and start drying your hair.

[How to use]

• Attach the Styling Nozzle

• Dampen the part you want to style with water, etc.

• Select LOW with the airflow button

• Select HOT with the air temperature button, and aim the airflow at your hair

Dry your hair in this order: roots, main body of hair, then hair tips. The idea is to keep the dryer about 10 cm from your hair and move it slowly.

• When drying the inner or back sections of your hair, be careful not to cover the main unit with hair to prevent it from being sucked in

• The Quick-dry Roots Nozzle is recommended for people with long or thick hair, or when the air temperature feels low

・The air temperature differs depending on which attachments are used

When your hair is about 90% dry, select “Hot/Cold Mark (Arrow)” with the air heat switching button.
Divide your hair into roughly four sections and direct Hot/Cold airflow two or three times to each place while finger-combing to keep the hair taut. The trick is to finish by directing Hot/Cold airflow onto your hair from your scalp down towards your hair tips.

People who want to increase hair volume

Lift the roots of your hair and blow warm air from the bottom upwards.

People who want to decrease hair volume

Brush your hair with your fingers in the same direction as the hair growth and aim warm air from the top to the bottom.

Select “LOW” with the airflow switching button and “Hot/Cold Mark (Arrow)” with the air heat switching button.
Hold the dryer closer to your hair (about 5 cm) and direct the airflow to both sides of the hair tips while finger-combing them to neaten them. This will make your hair sleek and glossy right down to the tips.

Weighing approximately 550 g,^*3 it is easy on the arm and comfortable to hold, making it perfect for daily use. It is also ideal for travel and business trips.

Colours for the main unit have been developed using biomass paint^*4 made from plant-derived materials.
With colouring inspired by natural materials, a timeless look that fits any lifestyle is created.

In fitting with the popular Hair Dryer nanocare, we have even paid special attention to the packaging. The packaging and cushioning materials made from pulp have been designed leveraging a paper-like texture.